South African Class 5A 4-6-2

This article is about one of several different Cape Government Railways locomotive types to be designated "Karoo Class". For other CGR Karoo Class locomotives, see Cape Government Railways Karoo Class locomotives.

CGR Karoo Class 4-6-2 1903
South African Class 5A 4-6-2

CGR no. 903, SAR no. 721, Paardeneiland, c. 1940

Type and origin Power type Steam Designer Cape Government Railways (H.M. Beatty) Builder Kitson and Company Serial number 4193-4194 Model CGR Karoo Build date 1903 Total produced 2

Specifications Configuration 4-6-2 (Pacific) Driver axle 2nd coupled axle Gauge 3 ft 6 in (1,067 mm) Cape gauge Leading dia Coupled dia 60 in (1,524 mm) Trailing dia 33 in (838 mm) Tender wheels 37 in (940 mm) Wheelbase  • Engine  • Leading 6 ft (1,829 mm)  • Coupled 10 ft 10 in (3,302 mm)  • Tender 10 ft (3,048 mm) Wheel spacing (Assymetrical) 1-2: 5 ft 7 in (1,702 mm) 2-3: 5 ft 3 in (1,600 mm) Length 58 ft 9 in (17,907 mm) Height 12 ft 10 in (3,912 mm) Frame type Bar Axle load  • Leading  • 1st coupled  • 2nd coupled  • 3rd coupled  • Trailing  • Tender axle Axle 1: Axle 2: Axle 3: Adhesive weight Loco weight Tender weight Loco & tender weight Tender type YE (3 axle) Fuel type Coal Fuel capacity 5 LT 10 cwt (5.6 t) Water cap Boiler:  • Pitch  • Diameter  • Tube plates  • Small tubes 154:  • Firebox type Round-top Boiler pressure 180 psi (1,241 kPa) Safety valve Ramsbottom Firegrate area 26 sq ft (2.4 m2) Heating surface 1,427 sq ft (132.6 m2)  • Tubes 1,317 sq ft (122.4 m2)  • Firebox 110 sq ft (10 m2) Cylinders Two Cylinder size bore 26 in (660 mm) stroke Valve gear Stephenson Valve type Richardson slide valves Couplers Bell link-and-pin

Performance figures Tractive effort 20,030 lbf (89.1 kN) @ 75%

Career Operators Cape Government Railways South African Railways Class CGR Karoo Class SAR Class 5A Number in class 2 Numbers CGR 903-904 SAR 721-722 Delivered 1903 First run 1903 Withdrawn 1940

The centre coupled axle had flangeless wheels

The South African Railways Class 5A 4-6-2 of 1903 was a steam locomotive from the pre-Union era in the Cape of Good Hope.

In 1903, the Cape Government Railways placed two Karoo Class steam locomotives with a 4-6-2 Pacific type wheel arrangement in passenger service. In 1912, when they were assimilated into the South African Railways, they were renumbered and designated Class 5A.

Design

The Karoo Class of the Cape Government Railways (CGR) was the first tender locomotive with a 4-6-2 Pacific type wheel arrangement to be introduced in Africa. It was the logical development of the CGR 6th Class 2-6-2 Prairie type, which later became the Class 6Y on the South African Railways (SAR).

File:H.M. Beatty.jpg

H.M. Beatty

Designed by CGR Chief Locomotive Superintendent H.M. Beatty at the Salt River shops in Cape Town, it was acquired to cope with the increasing weight of passenger trains on the one in eighty gradients between Beaufort West and De Aar.

At the time, there was a general belief that any appreciable raising of the boiler pitch would result in a top-heavy locomotive. Since Beatty was very cautious about raising the boiler's centre line to more than twice the rail gauge, or 7 feet (2,134 millimetres), and in this case also to accommodate the large coupled wheels, he resorted to cutting the boiler shell and installing specially shaped pockets to obtain the required clearance. The locomotive had a bar frame, Stephenson valve gear and used saturated steam.

Manufacturer

In 1903, two of these locomotives were built by Kitson and Company, immediately after building the two 6th Class 2-6-2 locomotives, since their works numbers follow in sequence. They were numbered 903 and 904, but were not allocated class numbers by the CGR and instead became known as the Karoo Class, from the region of the Western System which they were designed to work in.

Kitson later used the Karoo design as basis for a batch of Pacific type locomotives, which it built for the Midland Railway of Western Australia.

Characteristics

One of the most striking features of the Karoo Class was the length of its boiler, which was accentuated by the extended smokebox. The length of the smokebox was over 8 feet (2,438 millimetres) and the distance between the boiler's tube-plates was .

The engine used Richardson slide valves, arranged above the cylinders and actuated by the Stephenson motion and rocker shafts. The eccentrics were fitted to the trailing coupled wheel axle, which resulted in exceptionally long valve connecting rods of .

South African Railways

When the Union of South Africa was established on 31 May 1910, the three Colonial government railways (CGR, Natal Government Railways and Central South African Railways) were united under a single administration to control and administer the railways, ports and harbours of the Union. Although the South African Railways and Harbours came into existence in 1910, the actual classification and renumbering of all the rolling stock of the three constituent railways required careful planning and was only implemented with effect from 1 January 1912.

In 1912, these two locomotives were renumbered 721 and 722 and designated Class 5A on the SAR.

Service

In service, the Class 5A locomotives performed excellently. Beatty's annual report for 1905 stated that they ran 159,000 miles (256,000 kilometres) before a failure occurred, that failure being a hot box. They spent most of their working lives in the Karoo, until they were displaced by larger locomotives. They were then placed in suburban service, working out of Cape Town, where they remained until they were withdrawn from service c. 1940.

Illustration

• SAR Class 5A (4-6-2).jpg

  Working a suburban train, c. 1930

• CGR Karoo Class no. SAR 721.jpg

  Ex CGR Karoo Class no. 903, SAR Class 5A no. 721, Paardeneiland, Cape Town, c. 1940